Freesco, NND, CDN, EOS

http://www.freesco.pl
Dzisiaj jest czwartek, 28 marca 2024, 10:32

Strefa czasowa UTC+2godz.




Nowy temat Odpowiedz w temacie  [ Posty: 2 ] 
Autor Wiadomość
Post: poniedziałek, 19 października 2009, 17:32 
Offline

Rejestracja: czwartek, 12 lutego 2009, 15:22
Posty: 60
Lokalizacja: Poznań
Witam,
Chciałem sprawdzić stan jednego z moich dysków na serwerze. Z racji tego, że dysk główny to padaka:

: [/] [] ()
[root@arcoserver ~]# smartctl -s on -T permissive -a -d ata /dev/hdc1
smartctl version 5.36 [i586-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG SP0401N
Serial Number:    S004J1TL500184
Firmware Version: TJ300-08
User Capacity:    40,060,403,712 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0
Local Time is:    Mon Oct 19 20:51:13 2009 CEST

==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x00)   Offline data collection activity
               was never started.
               Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)   The previous self-test routine completed
               without error or no self-test has ever
               been run.
Total time to complete Offline
data collection:        (1500) seconds.
Offline data collection
capabilities:           (0x1b) SMART execute Offline immediate.
               Auto Offline data collection on/off support.
               Suspend Offline collection upon new
               command.
               Offline surface scan supported.
               Self-test supported.
               No Conveyance Self-test supported.
               No Selective Self-test supported.
SMART capabilities:            (0x0003)   Saves SMART data before entering
               power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               No General Purpose Logging support.
Short self-test routine
recommended polling time:     (   1) minutes.
Extended self-test routine
recommended polling time:     (  25) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   001   001   025    Pre-fail  Always   FAILING_NOW 15552
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       8
  5 Reallocated_Sector_Ct   0x0033   100   100   011    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   100   051    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0025   100   100   015    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       74131
 10 Spin_Retry_Count        0x0033   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0012   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       5
194 Temperature_Celsius     0x0022   136   136   000    Old_age   Always       -       34
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       1924
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x000a   100   100   051    Old_age   Always       -       0
201 Soft_Read_Error_Rate    0x000a   100   100   051    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 1
   CR = Command Register [HEX]
   FR = Features Register [HEX]
   SC = Sector Count Register [HEX]
   SN = Sector Number Register [HEX]
   CL = Cylinder Low Register [HEX]
   CH = Cylinder High Register [HEX]
   DH = Device/Head Register [HEX]
   DC = Device Command Register [HEX]
   ER = Error register [HEX]
   ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 613 hours (25 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  04 51 00 00 4f c2 e0  Error: ABRT

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  b0 da 00 00 4f c2 e0 00   4d+15:17:30.750  SMART RETURN STATUS
  ec 00 00 76 ea 03 e0 00   4d+15:17:30.750  IDENTIFY DEVICE
  ef 02 00 00 00 00 e0 00      00:00:47.938  SET FEATURES [Enable write cache]
  c6 00 10 00 00 00 e0 00      00:00:47.938  SET MULTIPLE MODE
  f8 00 00 00 00 00 e0 00      00:00:47.938  READ NATIVE MAX ADDRESS

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Device does not support Selective Self Tests/Logging


..chce wykorzystać drugi dysk. Jednak nie moge sprawdzić jego stanu gdyż otrzymuje błąd wejscia/wyjścia:

: [/] [] ()
[root@arcoserver ~]# smartctl -s on -T permissive -a -d ata /dev/hdd1
smartctl version 5.36 [i586-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Maxtor Fireball 3 family
Device Model:     Maxtor 2F030J0
Serial Number:    F12RCWXE
Firmware Version: VAM51JJ0
User Capacity:    30,750,031,872 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0
Local Time is:    Mon Oct 19 20:52:58 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
Error SMART Enable failed: Błąd wejścia/wyjścia
Smartctl: SMART Enable Failed.

SMART Disabled. Use option -s with argument 'on' to enable it.


Komuś znany jest ten błąd i jak sobie z nim poradzić??


Na górę
 Wyświetl profil  
 
 Tytuł:
Post: piątek, 23 października 2009, 23:14 
Offline
MODERATOR

Rejestracja: środa, 24 października 2007, 15:30
Posty: 329
Lokalizacja: Sadowne
: [/] [] ()
SMART support is: Disabled


Włącz SMART dla tego dysku...

_________________
Polska Grupa Freesco
medhost - Kompleksowe rozwiązania informatyczne
Przychodnia Optima Koszarska Rudnicka


Na górę
 Wyświetl profil  
 
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 2 ] 

Strefa czasowa UTC+2godz.


Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 22 gości


Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów
Nie możesz dodawać załączników

Szukaj:
Przejdź do:  
cron
Technologię dostarcza phpBB® Forum Software © phpBB Group
Hosting: Compus-Net
RobertKonik.pl