Freesco, NND, CDN, EOS

# [ISP settings for dial-up router]
ISPNAME=TPSA-SDI      # 30.ISP/connection name
PHONUM="[4~T1"   # 31.Dialing method P/T and phone numbers (tutaj nie kumam, wpisałem w konfiguratorze samo "T1" a w pliku są jakieś krzaczki)
LINKUP=1      # 32.Link up time, see DRULES
DRULES="accept any 1 any"   # 32."Bring_up_link rule" part of diald.conf
DNSADDR=194.204.159.1   # 33.Primary DNS server
DNSADDR1=194.204.152.34   # 34.Secondary DNS server
PROXY=         # 35.Host http proxy address
ADRTYPE=      # 36.If ISP supplies us with dynamic IP, then:
LOCAL=213.77.140.104     # 37.fake local side ppp IP addr (na wszelki wypadek wpisałem ale to chyba niekonieczne, bo po co...?)
REMOTE=   # 38.fake remote IP addr
AUTHMET=pap      # 40.Authentification method - pap/chap/script (czy aby dobrze wybrałem: pap?)    
Q0=''   # Chat sequence or
R0='Przemo'   # username for pap/chap
Q1=''
R1='powers'   # password for pap/chap
Q2=''
R2=''
Q3=''
R3=''

# [System]
ROUTER=dialup         #  0.dialup/leased/ethernet/bridge
HOSTNAME=routerek         #711.Router name
DOMAIN=1         #712.(Local) domain name
ENAMSQ=y           # 11.Enable NAT and firewall
ENABRG=n          # 12.Enable bridging mode? DONT TOUCH!!!
BIGMEM=n          # 13.If 16+MB RAM start ppp bsd compression
SAVERS=0,0           # 14.Savers - screen(min),hdd(x5 sec) 0 -off
SWPSIZE=0         # 15.Swap size in Kb on boot device. 0 - off
LOGSIZE=[4~[4~1000      # 16.System_log,logins_log sizes (bytes) (cholera, znowu jakieś krzaczki, skąd one się biorą? powinno być samo "1000")
DEFISP=         #  6.Default dialup ISP

# [Services]          #    y - worldwide/s - local/n - disable
ENADNS=n          #411.Enable caching DNS server
LOGDNS=n         #412.Enable debug info
ENADHCP=n          #421.Enable DHCP server
WINSADDR=         #422.   WINS address (for DHCP server)
LIZTIME=604800,604800      #423.   default-lease-time,max-lease-time
ENAWWW=n          #431.Enable Public HTTP Server
WWWPORT=80          #432.   on port
ENAWWA=s          #441.Enable Time Server  and control via HTTP
WWAPORT=82          #442.   on port
TIMADDR=www.clock.org      #443.Host timeserver address, empty - disable
TIMZONE=+0100         #444.   Offset to UTC (-1200 -:- +1200)
ENALPD=n          #451.Enable Print Server
LPPORT1=515         #452.   on port
LPDEV1=lp1         #453.   on output device
LPPORT2=516         #454.Second lp server on port, empty - disable
LPDEV2=lp2         #455.   on output device
ENATEL=s         # 46.Enable telnet server


# [Security]
TRUSTLN=p          #211.Trust local nets y/n/p{artual}
TRUSTMD=y         #212.Modem links have access to local networks
RINGS=2,7         #220.Rings before answer at login,nologin time
MonTIM=""         #221.Nologin times for modem users
TueTIM=""         #222
WedTIM=""         #223
ThuTIM=""         #224
FriTIM=""         #225
SatTIM=""         #226
SunTIM=""         #227


# [Modems]
MODEM0=cua1          # 51.1st modem
MSPEED0=115200         # 52.port's speed
MINIT0="ATZ"         # 53.init string (może init string musi być jakiś inny?)
MTU0=            #541.Maximum Transmit Unit
MRU0=            #542.Maximum Receive Unit
MADDR0=192.168.168.2      # 55.ppp link remote addr (for dialin purpose) (co to jest???)

MODEM1=          # 61
MSPEED1=         # 62
MINIT1=""         # 63
MTU1=            #641
MRU1=            #642
MADDR1=192.168.168.3      # 65.I said for dialin purpose.


# [leased line router]
ADRTYPE=            #921.if ISP supplies us with dynamic IP, then:
LOCAL=213.77.140.104        #922.fake local side ppp IP addr
REMOTE=127.0.0.3       #923.fake remote addr (co to jest???)


# [ethernet/leased/printer/ras router]
GATEWAY=         #911.Default gateway, if exist.
DNSADDR=127.0.0.1      #912.Primary DNS address for ethernet connection
DNSADDR1=      #913.Secondary DNS address for ethernet connection
PROXY=""      #914.HTTP proxy addr[:port]


# [Hardware]
IO0=0         #811.1st ethernet card I/O address
IRQ0=0            #812.IRQ line
IO1=0         #821
IRQ1=0            #822
IO2=0         #831
IRQ2=0            #832


# [Networks]
USEDHCP0=n         #720.Use DHCP client to config this interface
INTNAME0=eth0         #721.Interface name (eth0|arc0e|arc0)
DHCPLOG=y         #722.Enable DHCP client messages in the log
DHCPDNS=y         #723 Enable auto configuration of DNS via DHCP
IPADDR0=192.168.0.1      #724.IP adress of this interface
NETMASK0=255.255.255.0       #725.Network mask
NETWORK0=192.168.0.0      #    Network address
BRDCAST0=192.168.0.255      #    Broadcast address
            #726.IP pool, empty disables DHCP on this interface
IPRANGE0="192.168.0.2-192.168.0.7"

INTNAME1=         #731.Interface name (eth1|eth0:1|arc0e|arc0 etc)
IPADDR1=      #732. Second network
NETMASK1=
NETWORK1=
BRDCAST1=
IPRANGE1=""

INTNAME2=         #74x. Third network
IPADDR2=
NETMASK2=
NETWORK2=
BRDCAST2=
IPRANGE2=""

# [ISP settings for dial-up router]
ISPNAME=sdi             # 30.ISP/connection name
PHONUM="T1"     # 31.Dialing method P/T and phone numbers
LINKUP=1                # 32.Link up time, see DRULES
DRULES="accept any 1 any"       # 32."Bring_up_link rule" part of diald.conf
DNSADDR=194.204.159.1   # 33.Primary DNS server
DNSADDR1=194.204.152.34 # 34.Secondary DNS server
PROXY=                  # 35.Host http proxy address
ADRTYPE=dynamic         # 36.If ISP supplies us with dynamic IP, then:
LOCAL=127.0.0.2         # 37.fake local side ppp IP addr
REMOTE=127.0.0.3        # 38.fake remote IP addr
AUTHMET=pap             # 40.Authentification method - pap/chap/script
Q0=''   # Chat sequence or
R0='USER'       # username for pap/chap
Q1=''
R1='PASSWORD'    # password for pap/chap
Q2=''
R2=''
Q3=''
R3=''