Witam.
Jestem poczatkujacym uzytkownikiem neo. I mam takie problem. Po skonfigurowaniu fressco 3.2 wg instrukcji by Maciek (dla rj45) siec LAN mam tzn przydzielane mi sa adresy ip przez DHCP jednak nie mam internetu:(. Tzn polecenie ping
www.onet.pl na routerze daje mi unknow host. I zbytnio nie wiem co z tym robic bo podczas ladowania sie freesco nie wyskakuja zadne bledy. Posiadam modem adsl Aztech dls turbo 900. z wyjsciem ethernetowym. Jedynce co mozna dziwnego (dla mnie ) zobaczyc w logach to linijka :
CHAP authentication failed
Nie wiem czym to moze byc spowodowane(bo login i haslo mam dobre) jezeli chodzi o plik raport to wyglada on tak. (ps jak mam wyeksportowac ustawienia do pliku? lub gdzie one sa?)Sorki za takie pytanie ale jestem laikiem:(:(
FREESCO v0.3.2 System Report. Generated - Wed Oct 12 12:58:57 2005
----- clock -----
Wed Oct 12 12:59:00 2005
----- cat /etc/system.cfg -----
# [System]
ROUTER=ethernet # dialup/leased/ethernet/bridge
HOSTNAME=router #611.Router name
DOMAIN=inet #612.(Local) domain name
ENAMSQ=y #11.Enable NAT and firewall
ENAPING=y #112. Enable ICMP responses.
ENABRG=n #12.Enable bridging mode
BIGMEM=n #13.If 16+MB RAM start ile command line history.
RAMDRIVE=n #13.If 17+MB RAM you can enable ramdrives
SAVERS=10,0 #14.Savers - screen(min),hdd(x5 sec) 0 -off
SWPSIZE=0 #15.Swap size in MB on boot device. 0 - off
LOGSIZE=50000,5000 #16.System_log,logins_log sizes (bytes)
ENABEEP=y #17.Enable beeps for certain events
ENAMON=n #20. Enamble flashing leds for Internet packets
COLORS=y #21. Enable console colors
ENAPNP=n #22. Enable ISA PnP
DEFISP= # Default dialup ISP
RDONLY=n #10. Make Freesco run entirely in ram with no disk usage.
# [Debug]
LOGDNS=n #412.Log DNS requests
LOGHTTP=n #182.HTTP/control logging
LOGCHAT=n #183.Dialout chat script debug logging
LOGPPPD=n #184.pppd debug logging
LOGDIALD=n #185.diald verbose logging
LOGIDENT=s #186.Debug ident or (s)tandard logging
LOGNET=1 #187.Log level for Netmeeting 0 to 4
LOGFTP=s #188.Debug FTP or (s)tandard logging
LOGFIRE=y #189.Log default firewall.
# [Services] # y - worldwide/s - local/n - disable
ENADNS=s #41.Enable caching DNS server
DNSCACHE=500 #411.Number of URL's to cache. 0 to dissable caching
ENACRON=n #42. Enable Cron deamon
ENADHCP=y #431.Enable DHCP server
WINSADDR= #432. WINS address (if external)
LIZTIME=604800,604800 #433,434 default-lease-time,max-lease-time
ENAWWW=y #441.Enable Public HTTP Server
WWWPORT=80 #442. on port
ENAWWA=s #451.Enable Time Server and control via HTTP
WWAPORT=82 #452. on port
TIMADDR=www.clock.org #453.Host timeserver address, empty - disable
TIMZONE=+0100 #454. Offset to UTC (-1200 -:- +1200)
ENALPD=n #461.Enable Print Servers
ENATEL=n #47. Enable telnet server
ENADYNDNS=n #49. Enable dynamic name client.
ENAID=n #50. Enable ident server.
ENAFTP=n #51. Enable FTP server.
FTPPORT=21 #512. on port.
FTPCON=5 #513. Maximum allowed FTP connections.
FTPANON=n #514. Enable anonymous FTP connections.
PKGDOMAIN=http://www.freescosoft.com/home/0.3.x/ # Default package domain.
PKGDIR=/www/downloads # Default package save directory.
# [ Print server #1 ]
ALLOWED0=1 # A picture that all client IP's must match.
LPPORT0=515
LPDEV0=lp1
# [Security]
TRUSTLN=n #241.Trust local nets y/n/p{artual}
TRUSTMD=n #242.Modem links have access to local networks
RINGS=3,8 #220.Rings before answer at login,nologin time
MonTIM="" #221.Nologin times for modem users
TueTIM=""
WedTIM=""
ThuTIM=""
FriTIM=""
SatTIM=""
SunTIM=""
# [Hardware COM Ports]
# [Modems]
MINIT0="ATZ"
MTUALL= # MTU for all dial-in links
MRUALL= # MRU for all dial-in links
# [ diald ]
RDTOUT= #821 delay between dialing attempts (seconds)
RTRCNT= #822 maximum number of initial attempts
DRTRCNT= #823 maximum number of restoring attempts
RBKOFF= #824 increase redial timeout after failure (seconds)
DFAILIM= #825 maximum number of consecutive failed attempts
FPTOUT= #826 timeout of the very first packet sent (seconds)
# [leased line router]
ADRTYPE= #921.if ISP supplies us with dynamic IP, then:
LOCAL= #922.fake local side ppp IP addr
REMOTE= #923.fake remote addr
# [ethernet/leased/printer/ras router]
GATEWAY= #62. 631.Default gateway, if exist.
DNSADDR=194.204.159.1 #414.Primary DNS address for ethernet connection
DNSADDR1=194.204.152.34 #415.Secondary DNS address for ethernet connection
PROXY="" #914.HTTP proxy addr[:port]
# [Ethernet hardware]
IO0=0
IRQ0=0
IO1=0
IRQ1=x
# [Network 0]
USEDHCP0=y #720. Use DHCP client to config this interface
DHCPLOG=n #722. Enable DHCP client messages in the log
DHCPDNS=y #723. Enable auto configuration of DNS via DHCP
USEPPP0=y #626. Use PPP on this interface
PPPTYPE=o #626. PPP ethernet protocal PPP(o)E PP(t)P.
PPPRT=n #626. Add a default route to PPP ethernet.
CLAMPMSS= #630. Clamp MSS (packet rewriting)
EPPPMTU0= #632. Maximum Transmit Unit.
INTNAME0=eth0 # Interface name (eth0|arc0e|arc0)
IPADDR0=192.168.0.1 # IP adress of this interface
NETMASK0=255.255.255.0 # Network mask
NETWORK0=192.168.0.0 # Network address
BRDCAST0=192.168.0.255 # Broadcast address
IPRANGE0="" # IP pool, empty disables DHCP on this interface
# [Network 1]
INTNAME1=eth1 # Interface name (eth1|arc1e|arc1)
IPADDR1=192.168.1.1 # IP adress of this interface
NETMASK1=255.255.255.0 # Network mask
NETWORK1=192.168.1.0 # Network address
BRDCAST1=192.168.1.255 # Broadcast address
IPRANGE1="192.168.1.20 192.168.1.240" # IP pool, empty disables DHCP on this interface
----- cat /etc/live.cfg -----
BOOTMOD=
VERSION=0.3.2
BOOTDEV=fd0
BOOTIME="Wed Oct 12 12:52:16 2005"
----- cat /etc/dhcpc/dhcpcd-eth0.info -----
----- cat /etc/portfw.cfg | sed s/\#.*// -----
----- cat /etc/banlist.cfg | sed s/\#.*// -----
----- sed -n 1,/Secret/P /etc/chat.pwd -----
# [ISP settings for permanent connection]
DNSADDR=194.204.159.1
DNSADDR1=194.204.152.34
ISPNAME=ethernet # Dont edit ISP name
GATEWAY=
USEPEERDNS=y
PROXY=
#---Secret Part---
----- lsmod -----
Module Pages Used by
rtl8139.o-n 3 2
ip_masq_netmeeting 2 0
ip_masq_ftp 1 0
ip_masq_irc 1 0
ip_masq_vdolive 1 0
ip_masq_raudio 1 0
ip_masq_icq 1 0
ip_masq_cuseeme 1 0
8390 2 0
----- dmesg | grep eth -----
eth0: RealTek RTL8139 Fast Ethernet at 0xfc00, IRQ 10, 00:c1:26:08:8f:97.
eth1: RealTek RTL8139 Fast Ethernet at 0xf800, IRQ 10, 00:50:ba:d4:b0:6f.
----- ifconfig -----
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:26 errors:0 dropped:0 overruns:0
TX packets:26 errors:0 dropped:0 overruns:0
eth0 Link encap:10Mbps Ethernet HWaddr 00:C1:26:08:8F:97
inet addr:255.255.255.255 Bcast:255.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0
TX packets:28 errors:0 dropped:0 overruns:0
Interrupt:10 Base address:0xfc00
eth1 Link encap:10Mbps Ethernet HWaddr 00:50:BA:D4:B0:6F
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:10 Base address:0xf800
Bardzo prosze o pomoc.
Pozdrawiam