tak wywala no target no chain...

iptables v1.3.1

Usage: iptables -[AD] chain rule-specification [options]
iptables -[RI] chain rulenum rule-specification [options]
iptables -D chain rulenum [options]
iptables -[LFZ] [chain] [options]
iptables -[NX] chain
iptables -E old-chain-name new-chain-name
iptables -P chain target [options]
iptables -h (print this help information)

Commands:
Either long or short options are allowed.
--append -A chain Append to chain
--delete -D chain Delete matching rule from chain
--delete -D chain rulenum
Delete rule rulenum (1 = first) from chain
--insert -I chain [rulenum]
Insert in chain as rulenum (default 1=first)
--replace -R chain rulenum
Replace rule rulenum (1 = first) in chain
--list -L [chain] List the rules in a chain or all chains
--flush -F [chain] Delete all rules in chain or all chains
--zero -Z [chain] Zero counters in chain or all chains
--new -N chain Create a new user-defined chain
--delete-chain
-X [chain] Delete a user-defined chain
--policy -P chain target
Change policy on chain to target
--rename-chain
-E old-chain new-chain
Change chain name, (moving any references)
Options:
--proto -p [!] proto protocol: by number or name, eg. `tcp'
--source -s [!] address[/mask]
source specification
--destination -d [!] address[/mask]
destination specification
--in-interface -i [!] input name[+]
network interface name ([+] for wildcard)
--jump -j target
target for rule (may load target extension)
--match -m match
extended match (may load extension)
--numeric -n numeric output of addresses and ports
--out-interface -o [!] output name[+]
network interface name ([+] for wildcard)
--table -t table table to manipulate (default: `filter')
--verbose -v verbose mode
--line-numbers print line numbers when listing
--exact -x expand numbers (display exact values)
[!] --fragment -f match second or further fragments only
--modprobe=<command> try to insert modules using this command
--set-counters PKTS BYTES set the counter during insert/append
[!] --version -V print package version.

IPP2P v0.7.2 options:
--ipp2p Grab all known p2p packets
--ipp2p-data Identify all known p2p download commands (obsolete)

--edk [TCP&UDP] All known eDonkey/eMule/Overnet packets
--dc [TCP] All known Direct Connect packets
--kazaa [TCP&UDP] All known KaZaA packets
--gnu [TCP&UDP] All known Gnutella packets
--bit [TCP&UDP] All known BitTorrent packets
--apple [TCP] All known AppleJuice packets (beta - just a few tests until now)
--winmx [TCP] All known WinMX (beta - need feedback)
--soul [TCP] All known SoulSeek (beta - need feedback!)
--ares [TCP] All known Ares - use with DROP only (beta - need feedback!)

--edk-data [TCP] eDonkey/eMule/Overnet download commands (obsolete)
--dc-data [TCP] Direct Connect download command (obsolete)
--kazaa-data [TCP] KaZaA download command (obsolete)
--gnu-data [TCP] Gnutella download command (obsolete)

Note that the follwing options will have the same meaning:
'--ipp2p' is equal to '--edk --dc --kazaa --gnu'
'--ipp2p-data' is equal to '--edk-data --dc-data --kazaa-data --gnu-data'

IPP2P was intended for TCP only. Due to increasing usage of UDP we needed to change this.
You can now use -p udp to search UDP packets only or without -p switch to search UDP and TCP packets.

See README included with this package for more details or visit http://www.ipp2p.org

Examples:
iptables -A FORWARD -m ipp2p --ipp2p -j MARK --set-mark 0x01
iptables -A FORWARD -p udp -m ipp2p --kazaa --bit -j DROP
iptables -A FORWARD -p tcp -m ipp2p --edk --soul -j DROP

no działa tzn bledu nie wywala ale emule sie laczy :/