Domyslem sie, ze ten konfig jest w: /boot/isolinux/kconfig
i sa to sekcje urzadzen blokowych. to niech mi tylko ktos to rozszyfruje co to za typu urzadzen albo wg jakiego klucza jest ta rozpiska:
# SCSI low-level drivers
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=15000
# CONFIG_AIC79XX_BUILD_FIRMWARE is not set
# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
# CONFIG_AIC79XX_DEBUG_ENABLE is not set
CONFIG_AIC79XX_DEBUG_MASK=0
# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_MEGARAID2 is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
# CONFIG_SCSI_NCR53C8XX is not set
CONFIG_SCSI_SYM53C8XX=m
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4
CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32
CONFIG_SCSI_NCR53C8XX_SYNC=20
# CONFIG_SCSI_NCR53C8XX_PROFILE is not set
# CONFIG_SCSI_NCR53C8XX_IOMAPPED is not set
# CONFIG_SCSI_NCR53C8XX_PQS_PDS is not set
# CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
Jak znam zycei to te z EATA i SATA mozemy wyrzucic - ale zo z pozostalymi. Interesuje mnie zrobienie maszyny ktora miala by raida w 5 i ja sie domyslam poza konterolerem i dyskami
cos jeszcze pewnie musz tu zmienic.
PS soory za tak proste pytania ale tak gleboko to jeszcze sie nie bawilem.
Dzieki za odpowiedz.
Artur