Freesco, NND, CDN, EOS :: Wyświetl temat - WAN modem router adsl !!??

: [/] [] ()

[root@router_nnd triplex]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:48:54:50:FF:66
          inet addr:10.0.0.13  Bcast:10.255.255.255  Mask:255.0.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:15140 errors:0 dropped:0 overruns:0 frame:0
          TX packets:17682 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7333245 (6.9 Mb)  TX bytes:11181680 (10.6 Mb)
          Interrupt:11 Base address:0xdc00

eth1      Link encap:Ethernet  HWaddr 00:50:BA:D5:2D:8E
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:18055 errors:0 dropped:0 overruns:0 frame:0
          TX packets:15344 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:11220502 (10.7 Mb)  TX bytes:7389552 (7.0 Mb)
          Interrupt:10 Base address:0xf800

[root@router_nnd triplex]#

Autor:	Anonymous [ poniedziałek, 17 października 2005, 11:23 ]
Tytuł:	WAN modem router adsl !!??
Witam! Mam takie pytanie kto wiek jak skonfigurowac madem router ADSL? A dokładniejj wyjscie wan?:( Dodam ze to router adsl firmy mercury na układie conexant. a model to art18cxa link do manuala. http://www.mercury-pc.com/downloads_lis ... ductid=376 Problem jest taki ze server jest sknonfigurowany poprawnie to znaczy dodale sieciowke i n eth0 ustawilem parametry, no i tu najlepsze wszystko dziala ? mam takie parametry : [/] [] () [root@router_nnd triplex]# ifconfig eth0 Link encap:Ethernet HWaddr 00:48:54:50:FF:66 inet addr:10.0.0.13 Bcast:10.255.255.255 Mask:255.0.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15140 errors:0 dropped:0 overruns:0 frame:0 TX packets:17682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7333245 (6.9 Mb) TX bytes:11181680 (10.6 Mb) Interrupt:11 Base address:0xdc00 eth1 Link encap:Ethernet HWaddr 00:50:BA:D5:2D:8E inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18055 errors:0 dropped:0 overruns:0 frame:0 TX packets:15344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11220502 (10.7 Mb) TX bytes:7389552 (7.0 Mb) Interrupt:10 Base address:0xf800 [root@router_nnd triplex]# GeSHi © Codebox Plus wszystkie dane sa statyczne. Ja to zrobilem tak jak dla uzytkownika po prostu podalem mu ip uzytkownika i tyle ale to nie jest tak jak powinno byc tak jak dla portu wan czyli 213.!!!!. a druga sprawa niedziala mi dobrze program ez-ipupdate ( oczywiscie zmiany sa wprowadzone poprawnie w configu bo dodam wczesniej mialem neo na thompson na usb ale mialem problemy z praca tego sprzetu) Po aktualizacji programu ukazuje mi sie cos takiego : [/] [] () ez-ipupdate Version 3.0.11b8 Copyright (C) 1998-2001 Angus Mackay. no update needed at this time GeSHi © Codebox Plus Pomocy pozdrawiam

Autor:	tasiorek [ poniedziałek, 17 października 2005, 11:56 ]
Tytuł:
Nie bardzo rozumiem co chcesz osiagnac, ale jak chcesz poprostu miec neta to zrob tak: Skonfiguruj polaczenie na routerze (wszystkie parametry ustaw tu a nie na nnd), podlacz go do kompa z nnd kablem ethernetowym i w net_confie wybierz opcje dsl, albo klient dhcp.

Autor:	zciech [ poniedziałek, 17 października 2005, 11:59 ]
Tytuł:
W tej chwili w modemie masz wlaczana maskarade. To nic dziwnego ze ez-update nie chce ci zmieniac IP bo i nie ma co zmieniac Powinienes przelaczyc modem w tryb bridge a jak sadze w net_confie wybrac modem na rj45 czyli PPPoE.

Autor:	Anonymous [ poniedziałek, 17 października 2005, 12:27 ]
Tytuł:
Tak tyko ze ja bałwan jestem ominac router w tym modemie adsl i miec wan! Po tak jak napisales "tasiorek" to wszystko chodi tyko ze niemozna ustawic adresu zewnetrznego dla ez-update i niemam domeny. Po prostu z zewnatrz nie mozna sie dostac:( a to jest potrzebne...!! a ktos moze patrzal na manuala? moze wam fachowcom to cos powie bo dlamnie to czrna magia:) P>S zciech twoj post tez niedaje efektow:( Na moim adsl router znalazlem help'a i napewno w nim jest sporo waznych rzeczy:) tyko ja niemma pojecia. WAN Configuration The WAN configuration page allows the user to set the configuration for the WAN/ADSL ports. * Per VC Settings Under Per VC Setting, it provides the configurations for VPI/VCI, Static IP Address Subnet Mask, and Gateway. The Static IP Address, Subnet Mask and Gateway are used for Static IP configuration. Current Conexant firmware supports eight PVCs. To switch between the PVCs, please choose the options of virtual circuit and click on the Submit button to switch. * MAC Spoofing The MAC Spoofing is developed to solve the scenario when the ISP only recognizes one MAC address. Enter the ISP recognized MAC address here. * ATM * Service Category UBR and CBR are supported from the ATM. * Bandwidth Bandwidth setting takes effect only when the CBR is selected. The maximum available bandwidth is from the upstream data rate of ADSL status page. * Encapsulation Choose appropriate ADSL encapsulation. * Bridge * Bridge Mode Configuration In a typical bridged configuration, the ADSL router is transparent to the network. It bridges the ADSL line to the Ethernet line, making both sides appear as a single subnet. In this configuration, an IP address only needs to be provided to the PC. It may still be beneficial to provide an IP address to the ADSL router for management. * Router Mode Configuration In a typical routed configuration, the ADSL router is treated as a separate device on the network that the PC and DSLAM send packets to. The Ethernet and ADSL networks are configured as separate IP subnets. The PC must have the ADSL router set up as its default gateway. * IGMP The Internet Group Management Protocol is the standard for IP multicasting in the Internet. It is used to establish host memberships in particular multicast groups on a single network. The mechanisms of the protocol allow a host to inform its local router, using Host Membership Reports, that it wants to receive messages addressed to a specific multicast group. * PPP The current release supports multiple PPP sessions per PVC. The PPP configuration in the WAN configuration page is for the first PPP session for each PVC. The predefined PPP Account Name (Account ID) is "Simple PPP Account 0" for PVC0 and predefined PPP Connection Name is "Simple PPP Session 0" for PVC0. For the other PVC X, the predefined account name and connection name will be "Simple PPP Account X" and "Simple PPP Session X". X is the PVC number from 1 to 7. It can support up to 16 PPP sessions, and each PVC can support up to 8 PPP sessions. The multiple PPP sessions may be configured with any combination over 8 PVCs. For the multiple PPP sessions, please go to the PPP Configuration page. * Service Name The service name of PPP is required by some ISPs. If the ISP does not provide the Service Name, please leave it blank. * Username and Password These are provided by the ISP. * Disconnect Timeout The Disconnect Timeout allows you to set the specific period of time to disconnect from the ISP. The default is 0, which means never disconnect from the ISP. * MRU Maximum Receive Unit indicates the maximum size of the PPP information field that this device can receive. The default value is 1492 and is used in the beginning of the PPP negotiation. In the normal negotiation, the peer will accept this MRU and will not send packets with an information field larger than this value. * MTU Maximum Transmission Unit indicates the largest physical packet size, measured in bytes that a network can transmit. Any messages larger than the MTU are divided into smaller packets before being sent. Trial and error is the only sure way of finding the optimal MTU but it has been set to 1492 by default. * MSS Maximum Segment Size is the largest size of data that TCP will send in a single IP packet. When a connection is established between a LAN client and a host in the WAN side, the LAN client and the WAN host will indicate their MSS during the TCP connection handshake. The default value is 1432. * Authentication When the AUTO option is chosen, the PAP mode will run first then CHAP. * Automatic Reconnect When it is checked, it will maintain the PPP connection all the time. If the ISP shuts down the PPP connection, it will automatically reconnect the PPP session. Save the changes and the router must reset for the changes to take effect. WAN Status The WAN Status page shows the information and status of WAN PVCs. WAN: These fields display the IP address, Subnet Mask and MAC address for the WAN (ADSL) interface. Use the Virtual Circuit selection to selection different PVC for status display. DHCP Release and Renew: This field allows the user to release and renew the WAN IP address in the WAN DHCP Client Enabled (dynamic)

Autor:	tasiorek [ poniedziałek, 17 października 2005, 13:31 ]
Tytuł:
W taki mrazie zacznij od podania jakie masz lacze. Co do modemu to nie grzeb w konfiguracji, tylko zmien tam tryb na bridge jak Ci zciech napisal, bo cala reszte trzeba ustawic na nnd.

Freesco, NND, CDN, EOS http://forum.freesco.pl/

WAN modem router adsl !!?? http://forum.freesco.pl/viewtopic.php?f=22&t=9472	Strona 1 z 1

Autor:	Mis' [ poniedziałek, 17 października 2005, 15:14 ]
Tytuł:
teamc pisze: Wszystko chodzi tak jak poinno:) Oprócz twojej polszczyzny. W podzięce za pomoc obiecaj nam, że zawsze, powtarzam, zawsze zanim wciśniesz przycisk "Wyślij" będziesz czytał 3 razy to co napisałeś...

Strona 1 z 1	Strefa czasowa UTC+2godz.
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/

Autor:	Anonymous [ poniedziałek, 17 października 2005, 13:45 ]
Tytuł:
No i luz lepiej.lacze to neo 512 ze zmiennym ip. a modem t mercury z jednym wyjsciem rj45 i jednym wejdciem rj11. W konfigu modemu ma ustaiony juz bridge. I nadal ma ustawione stale ip jak dla zwyklego usera:(

Autor:	zciech [ poniedziałek, 17 października 2005, 13:54 ]
Tytuł:
http://www.planet.a.pl/filemanager/down ... 7.2004.pdf Poczytaj sobie to jest po polsku, dotyczy co prawda innego modemu ale zasada jest taka sama.

Autor:	Anonymous [ poniedziałek, 17 października 2005, 15:08 ]
Tytuł:
ZCIECH jestes super ten manual jest do mojego routera na chipe conexant W tym momecie bałwan jestem podziekowac wszystkim i jestem zadowolony z zakupu sprzetu:) bo kupilem mercur'ego a sie okazuje ze to samo jest w planet Wszystko chodzi tak jak poinno:)