Freesco, NND, CDN, EOS

errors:
Feb  7 13:42:26 server_nnd thttpd[336]: socket :: - Address family not supported by protocol
Feb  7 13:50:31 server_nnd kernel: [EAGLE-USB]  SM: LOS Defect
Feb  7 14:02:27 server_nnd pppoa[234]: read (AsyncReadFromPPP): Input/output error
Feb  7 14:03:59 server_nnd thttpd[525]: socket :: - Address family not supported by protocol
Feb  7 14:13:47 server_nnd kernel: [EAGLE-USB]  SM: LOS Defect
Feb  7 14:18:27 server_nnd pppoa[333]: read (AsyncReadFromPPP): Input/output error
Feb  7 14:19:50 server_nnd thttpd[558]: socket :: - Address family not supported by protocol
Feb  7 17:16:50 server_nnd dhcpd: Abandoning IP address 192.168.0.8: pinged before offer
Feb  7 19:42:15 server_nnd kernel: hub.c: already running port 1 disabled by hub (EMI?), re-enabling...
Feb  7 19:42:15 server_nnd pppoa[333]: recv (ReceivePacket): Network is down
Feb  7 19:42:15 server_nnd pppoa[333]: sendto (SendPPPPacket size: 44): No such device or address
Feb  7 19:49:49 server_nnd thttpd[558]: socket :: - Address family not supported by protocol
kernel:
Feb  7 19:42:15 server_nnd kernel: [Eagle-usb] transmit error with URB status -110
Feb  7 19:42:15 server_nnd last message repeated 5 times
Feb  7 19:42:15 server_nnd kernel: hub.c: already running port 1 disabled by hub (EMI?), re-enabling...
Feb  7 19:42:15 server_nnd kernel: usb.c: USB disconnect on device 00:14.2-1 address 2
Feb  7 19:42:15 server_nnd kernel: [eagle-usb] eu_irq : URB canceled by user.
Feb  7 19:42:15 server_nnd kernel: [eagle-usb] ADSL device removed
Feb  7 19:42:16 server_nnd kernel: hub.c: new USB device 00:14.2-1, assigned address 3
Feb  7 19:42:16 server_nnd kernel: [eagle-usb] New USB ADSL device detected, waiting for DSP code...
Feb  7 19:42:16 server_nnd kernel: [eagle-usb] created proc entry at : /proc/driver/eagle-usb/001-003
Feb  7 19:45:03 server_nnd kernel: [eagle-usb] ioctl EU_IO_OPTIONS received
Feb  7 19:45:03 server_nnd kernel: [eagle-usb] ioctl EU_IO_DSP received
Feb  7 19:45:03 server_nnd kernel: [eagle-usb] Loading DSP code to device...
Feb  7 19:45:03 server_nnd kernel: [eagle-usb] DSP code successfully loaded to device
Feb  7 19:45:32 server_nnd kernel: [eagle-usb] Modem operational !!
Feb  7 19:45:32 server_nnd kernel: [eagle-usb]  Ethernet device eth2 created.

Diagnostic (1.18 2004/11/04) driver eagle-usb 20050207201739
# System Information
Linux server_nnd 2.4.28-1nnd #1 Sun Dec 5 01:08:46 CET 2004 i586 unknown unknown GNU/Linux
other distrib
Linux version 2.4.28-1nnd (root@maupa) (gcc version 3.3.3) #1 Sun Dec 5 01:08:46 CET 2004
used : 3.3.3
# Dependances
Verify dependances on source by hand (kernel-source...)
drwxr-xr-x  2 root root 4096 Dec  5 01:44 linux
# Kernel config : usb modules
ppp_async               6400   1  (autoclean)
ppp_generic            14948   3  (autoclean) [ppp_async]
slhc                    4624   0  (autoclean) [ppp_generic]
uhci                   23708   0  (unused)
eagle-usb             109828   2
usbcore                57004   1  [uhci eagle-usb]
# pci & usb configuration (check for latency, only keep relevant lines about USB)
00:00.0 Host bridge: VIA Technologies, Inc. VT82C595/97 [Apollo VP2/97] (rev 06)
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0f.0 VGA compatible controller: S3 Inc. 86c775/86c785 [Trio 64V2/DX or /GX] (rev 16)
00:10.0 Network controller: Compaq Computer Corporation Integrated Netelligent 10/100 (rev 10)
00:14.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 41)
00:14.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06)
00:14.2 USB Controller: VIA Technologies, Inc. USB (rev 02)
00:14.3 Non-VGA unclassified device: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
PCI devices found:
  Bus  0, device   0, function  0:
    Host bridge: VIA Technologies, Inc. VT82C595/97 [Apollo VP2/97] (rev 6).
      Master Capable.  Latency=8.
  Bus  0, device  12, function  0:
    Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 16).
      IRQ 10.
      Master Capable.  Latency=66.  Min Gnt=32.Max Lat=64.
      I/O at 0x1100 [0x11ff].
      Non-prefetchable 32 bit memory at 0x46000000 [0x460000ff].
  Bus  0, device  15, function  0:
    VGA compatible controller: S3 Inc. 86c775/86c785 [Trio 64V2/DX or /GX] (rev 22).
      IRQ 11.
      Non-prefetchable 32 bit memory at 0x40000000 [0x43ffffff].
  Bus  0, device  16, function  0:
    Network controller: Compaq Computer Corporation Integrated Netelligent 10/100 (rev 16).
      IRQ 5.
      Master Capable.  Latency=66.
      I/O at 0x1020 [0x102f].
      Non-prefetchable 32 bit memory at 0x44000000 [0x4400000f].
  Bus  0, device  20, function  0:
    ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 65).
  Bus  0, device  20, function  1:
    IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 6).
      Master Capable.  Latency=66.
      I/O at 0x1030 [0x103f].
  Bus  0, device  20, function  2:
    USB Controller: VIA Technologies, Inc. USB (rev 2).
      IRQ 10.
      Master Capable.  Latency=66.
      I/O at 0x1000 [0x101f].
  Bus  0, device  20, function  3:
    Non-VGA unclassified device: VIA Technologies, Inc. VT82C586B ACPI (rev 16).
/usr/sbin/eaglediag: line 387: lsusb: command not found
# interruptions' affectation
           CPU0
  0:     172549          XT-PIC  timer
  1:          2          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  5:          0          XT-PIC  TLAN
  8:          1          XT-PIC  rtc
 10:     286702          XT-PIC  usb-uhci, eth0
 14:       5695          XT-PIC  ide0
NMI:          0
ERR:          0
/usr/sbin/eaglediag: line 400: hdparm: command not found
# disk uses dma ?        [ KO ]
# module loaded ?        [ OK ]
# modem operational ?    [ OK ]
eagle-usb status display
-------------------------------------------------------------
Driver version 2.0.0     Chipset: Eagle0
Vendor ID : 0x1110     Product ID : 0x9021   Rev: 0x500b
USB Bus : 001    USB Device : 002        Dbg mask: 0x0
Ethernet Interface : eth2
MAC: 00:60:4c:43:8c:02
Tx Rate         192  Rx Rate         768
FEC               0  Margin           37  Atten             0 dB
VID-CPE           0  VID-CO           28  HEC               0
VPI               0  VCI              35  Delin          GOOD
Cells Tx      63274  Cells Rx    1318851
Pkts Tx       30826  Pkts Rx       45126
OAM               0  Bad VPI           0  Bad CRC           5
Oversiz.          0

Modem is operational

# Config vpi/vci/encapsulation/isp :  23 6 (pppoa) PL01
# pppd launched ?        [ OK ]
# Service for connection [ OK ]
# /etc/resolv.conf should contain the DNS
nameserver 194.204.152.34
nameserver 217.98.63.164
eth0      Link encap:Ethernet  HWaddr 00:0A:CD:00:A1:D9
          inet addr:192.168.0.1  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:35438 errors:1 dropped:0 overruns:0 frame:0
          TX packets:48561 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2559023 (2.4 Mb)  TX bytes:62939481 (60.0 Mb)
          Interrupt:10 Base address:0xe000

eth1      Link encap:Ethernet  HWaddr 00:08:C7:1C:63:05
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:5 Base address:0x1020

eth2      Link encap:Ethernet  HWaddr 00:60:4C:43:8C:02
          UP BROADCAST RUNNING MULTICAST  MTU:65535  Metric:1
          RX packets:45127 errors:0 dropped:0 overruns:0 frame:0
          TX packets:30827 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:61745616 (58.8 Mb)  TX bytes:1952568 (1.8 Mb)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

ppp0      Link encap:Point-to-Point Protocol
          inet addr:xx.xx.xxx.xxx  P-t-P:213.25.2.180  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1500  Metric:1
          RX packets:45123 errors:0 dropped:0 overruns:0 frame:0
          TX packets:30822 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:61655291 (58.7 Mb)  TX bytes:1335938 (1.2 Mb)

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
213.25.2.180    0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth1
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         213.25.2.180    0.0.0.0         UG    0      0        0 ppp0
# ping IP ?              [ OK ]
# test DNS resolution ?  [ OK ]
##Complete diagnostic has been saved on /var/log/eagle-usb/eagle_diag_20050207201739.txt
##Please keep only relevant data and remove personal informations.

log kernel:
May 28 16:09:26 router_nnd kernel: [eagle-usb] New USB ADSL device detected, waiting for DSP code...
May 28 16:09:26 router_nnd kernel: [eagle-usb] created proc entry at : /proc/driver/eagle-usb/001-002
May 28 16:09:26 router_nnd kernel: [eagle-usb] ioctl EU_IO_OPTIONS received
May 28 16:09:26 router_nnd kernel: [eagle-usb] ioctl EU_IO_DSP received
May 28 16:09:26 router_nnd kernel: [eagle-usb] Loading DSP code to device...
May 28 16:09:26 router_nnd kernel: [eagle-usb] DSP code successfully loaded to device
May 28 16:09:56 router_nnd kernel: [eagle-usb] Modem operational !!
May 28 16:09:56 router_nnd kernel: [eagle-usb]  Ethernet device eth1 created.
May 28 16:09:57 router_nnd kernel: CSLIP: code copyright 1989 Regents of the University of California
May 28 16:09:57 router_nnd kernel: PPP generic driver version 2.4.2
May 28 16:10:41 router_nnd kernel: [eagle-usb] Modem operational !!
May 28 16:10:42 router_nnd kernel: [EAGLE-USB]  SM: LOS Defect
May 28 16:10:48 router_nnd last message repeated 2 times
May 28 16:10:48 router_nnd kernel: [eagle-usb] LOS Defect threshold reached.

log errors:
May 28 16:08:09 router_nnd kernel: [EAGLE-USB] EU_IO_GETIF: eth not yet created !!
May 28 16:10:01 router_nnd thttpd[303]: socket :: - Address family not supported by protocol
May 28 16:10:29 router_nnd pppoa[227]: read (AsyncReadFromPPP): Input/output error
May 28 16:10:42 router_nnd kernel: [EAGLE-USB]  SM: LOS Defect
May 28 16:10:48 router_nnd last message repeated 2 times
May 28 16:11:00 router_nnd pppoa[320]: read (AsyncReadFromPPP): Input/output error
May 28 16:11:31 router_nnd pppoa[325]: read (AsyncReadFromPPP): Input/output error
May 28 16:11:32 router_nnd kernel: [EAGLE-USB]  SM: LOS Defect
May 28 16:11:42 router_nnd last message repeated 3 times
May 28 16:12:02 router_nnd pppoa[334]: read (AsyncReadFromPPP): Input/output error
May 28 16:12:23 router_nnd kernel: [EAGLE-USB]  SM: LOS Defect
May 28 16:12:29 router_nnd last message repeated 2 times
May 28 16:12:34 router_nnd pppoa[339]: read (AsyncReadFromPPP): Input/output error
May 28 16:13:05 router_nnd pppoa[505]: read (AsyncReadFromPPP): Input/output error
May 28 16:13:12 router_nnd kernel: [EAGLE-USB]  SM: LOS Defect